系統版本
[root@ ~]# cat /etc/redhat-release
CentOS release 6.8 (Final)
[root@ ~]# uname -r
2.6.32-642.6.1.el6.x86_64
網卡說明
eth0 192.168.1.8（服務器外網卡）
eth1
eth2
兩塊服務器網卡(內網)
關閉防火墻
[root@ ~]# /etc/init.d/iptables stop
[root@ ~]# chkconfig iptables off
關閉selinux
[root@ ~]#setenforce 0
[root@ ~]#sed -i ‘s/SELINUX=enforcing/SELINUX=disabled/‘ /etc/selinux/config
禁用NetworkManager
[root@ ~]# /etc/init.d/NetworkManager stop
Stopping NetworkManager daemon: [ OK ]
[root@ ~]# chkconfig NetworkManager off
[root@ ~]# /etc/init.d/network restart
編輯eth1網卡
[root@ ~]# cd /etc/sysconfig/network-scripts/
[root@ network-scripts\]# cat >ifcfg-eth1 <<EOF
DEVICE=eth1
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
MASTER=bind0
EOF
編輯eth2網卡
[root@ network-scripts]# cat >ifcfg-eth2 <<EOF
DEVICE=eth2
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
MASTER=bind0
EOF
編輯bind0網卡
[root@ network-scripts]# cat >ifcfg-bind0 <<EOF
DEVICE=bind0
TYPE=Ethernet
ONBOOT=yes
BOOTPROTO=none
IPADDR=10.0.0.8
NETMASK=255.255.255.0
GATEWAY=10.0.0.254
IPV6INIT=no
USERCTL=no
EOF
配置bond參數
[root@ network-scripts]# cat >/etc/modprobe.conf <<EOF
alias bind0 bonding
options bind0 miimon=100 mode=6
EOF
加入開機自啟動(/etc/rc.local)
[root@ network-scripts]# cat >>/etc/rc.local <<EOF
ifenslave bind0 eth1 eth2
EOF
重啟網絡服務
[root@LVS-2 network-scripts]# service network restart
Shutting down interface eth0: [ OK ]
Shutting down interface eth1: [ OK ]
Shutting down interface eth2: [ OK ]
Shutting down loopback interface: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface bind0: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/.
Determining if ip address 10.0.0.8 is already in use for device bind0..[ OK ]
Bringing up interface eth0: Determining if ip address 192.168.1.8 is already in use for device eth0... [ OK ]
Bringing up interface eth1: RTNETLINK answers: File exists [ OK ]
Bringing up interface eth2: RTNETLINK answers: File exists [ OK ]
配置使綁定立即生效
[root@LVS-2 network-scripts]# ifenslave bind0 eth1 eth2
測試聯通
[root@LVS-2 network-scripts]# ping 10.0.0.8
PING 10.0.0.8 (10.0.0.8) 56(84) bytes of data.
64 bytes from 10.0.0.8: icmp_seq=1 ttl=64 time=0.089 ms
64 bytes from 10.0.0.8: icmp_seq=2 ttl=64 time=0.046 ms
^C
--- 10.0.0.8 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1921ms
rtt min/avg/max/mdev = 0.046/0.067/0.089/0.023 ms
此時會發現系統多一個網卡
[root@LVS-2 network-scripts]# ifconfig bind0
bind0
Link encap:Ethernet HWaddr 00:0C:29:CC:9B:5
inet addr:10.0.0.8 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fecc:9b55/64 Scope:LinkUP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:151 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:11826 (11.5 KiB) TX bytes:258 (258.0 b)
到此這篇關于Linux 系統雙網卡綁定配置實現的文章就介紹到這了,更多相關Linux 雙網卡綁定配置內容請搜索腳本之家以前的文章或繼續瀏覽下面的相關文章希望大家以后多多支持腳本之家！
